Class A is the top roof fire rating and Class C is the lowest one that still counts as rated. A Class A roof covering is effective against severe fire-test exposure, and a Class C covering is effective only against light exposure, according to UL's roof rating guide. The rating belongs to the tested roof assembly, not just the shingle, so the first step is to find out what is actually on your home.
If you own a South Florida home with asphalt shingles, this matters for insurance conversations, storm-season planning and the decision to preserve or replace an aging roof. Below, you get the plain meaning of each class, how the tests work, how fire classes differ from the Class 3 and Class 4 impact ratings people often mix them up with, and how to confirm what your roof carries.
TL;DR
- Class A is effective against severe fire exposure, Class B against moderate, and Class C against light exposure. Class A is the best rating.
- In the standard test, the maximum allowed flame spread is 6 feet for Class A and 13 feet for Class C.
- Fire Class (A, B, C) and impact Class (1 to 4) are two separate tests. Class C fire is not the same as Class 3 impact.
- The rating can depend on the shingle, underlayment and installation tested together, so check the manufacturer's documentation for your roof.
- Before you replace a roof over its age, call us for a free inspection so you know whether it qualifies for preservation instead.
Table of Contents
- What Class A, B and C actually mean
- How the fire test works
- Fire class is not impact class
- The rating belongs to the whole roof assembly
- How to check the fire rating of your roof
- Why condition matters as much as the label
- Class A vs Class C: how to decide
- What we offer before you replace
- Our perspective
- FAQ
- Sources
What Class A, B and C actually mean
Roof fire ratings come from a standardized test of how a roof covering behaves when fire starts outside the house: a spark, a burning ember or flaming debris landing on the roof. The letters rank how severe a fire exposure the covering handled.
| Class | Effective against | What it means for you |
|---|---|---|
| Class A | Severe fire-test exposure | The highest level of fire resistance for a roof covering |
| Class B | Moderate fire-test exposure | A middle tier |
| Class C | Light fire-test exposure | The lowest rated tier |
Those descriptions come straight from UL's explanation of the A, B and C roof ratings. A covering that fails to reach Class C is considered unclassified.
The University of California's wildfire mitigation guide for homeowners says Class A offers the best fire resistance and protection for a home. It also notes that the standard roof tests do not evaluate vulnerabilities at the roof edges, which is one reason a rating is a starting point and not a guarantee.
Most modern asphalt shingles sold today are manufactured to meet a Class A rating when installed as listed. Older roofs, or roofs built from different materials, may carry a lower class or an unknown one. Wood shakes, for example, are more prone to fire damage and cannot reach Class A on their own in the way a tested asphalt assembly can, so age and material both matter when you try to work out what you have.
How the fire test works
The test standard is ASTM E108, also published as UL 790. Roof coverings are exposed to an outside fire source with simulated wind. The test includes three elements:
- Spread of flame: a gas burner flame is applied to the roof surface, and the lab measures how far the fire travels.
- Intermittent flame: the flame is applied, removed and applied again, to see whether the covering keeps burning or recovers.
- Burning brands: burning pieces of wood are placed on the surface to mimic embers and flaming debris.
The lab uses a simulated 12 mph wind during the test. The Building America Solution Center confirms that Class A, B and C roofing must be tested under UL 790 or ASTM E108.
The numbers behind the letters
The clearest difference between the classes is flame spread. According to a roofing industry guide to Class A and Class 1 assemblies, the maximum allowable spread of flame is 6 feet for Class A roofs and 13 feet for Class C roofs. More than double the distance is a meaningful gap when embers land on a roof during a brush fire or a neighbor's fire.

A fair reading of these results: the ratings describe how a roof performed during specified test exposures. They do not promise a roof will be undamaged in a real fire, and they do not compare performance across every real-world condition, as Fire Engineering notes. Think of the class as a useful, standardized yardstick.
Fire class is not impact class
This is where many homeowners get tangled, and it is why the top search results for this topic talk about Class 3 and Class 4 shingles. Those are a different rating entirely.
- Fire rating (Class A, B, C): measured under UL 790 or ASTM E108. It asks how the roof handles fire from outside.
- Impact rating (Class 1 to 4): measured under UL 2218. It asks how the roof handles hail-like impact.
UL Solutions treats these as separate performance questions: UL 790 addresses flame, intermittent flame and burning-brand exposure, while UL 2218 addresses impact resistance. The impact standard's four ratings are based on replicating natural-hailstone impact energies by dropping steel balls from various heights. The Insurance Institute for Business and Home Safety (IBHS) identifies a Class 3 test as using a 1.75-inch steel ball, and Class 4 as using a 2-inch ball.
So a shingle can be listed as Class A for fire and Class 3 or Class 4 for impact at the same time. Class C fire does not equal Class 3 impact, and a Class 4 impact shingle is not automatically the best fire performer. IBHS, in its best-practices guidance, recommends Class 4 impact-rated products for hail protection and says shingles in wildfire-prone areas should carry a UL or ASTM Class A fire rating. Two different risks, two different labels.
In South Florida, wind-driven rain and storms are the daily story, and hail is less common than in Colorado or Texas. Fire ratings and wind ratings are likely to matter more to you than hail ratings. If you want to go further on wind, our guide on 4 vs. 6 shingle nails and what the label says about wind ratings is a good next read.
The rating belongs to the whole roof assembly
Homeowners tend to ask, "Are my shingles Class A?" The better question is, "Is my roof assembly Class A?"
UL explains that the UL 790 result can depend on the covering, underlayment and installation being evaluated together and used according to the listing. The deck underneath matters too: testing requirements differ significantly for combustible and noncombustible decks.
There are two practical consequences:
- Substitutions can change the answer. A roofing industry guide says substitutions in tested assemblies require FM or UL approval and may require additional testing. Without approval, they may affect insurance coverage or violate local codes.
- A Class A rating is not the whole picture. The same guide notes that Class A covers external fire performance only. It does not ensure building-code compliance, and it is not the same thing as a Class 1 rating, which is an FM Global designation that also tests for internal fire, wind uplift, foot traffic, corrosion, impact resistance and heat damage.
UL also says designers should set the minimum roof-assembly fire classification based on locally enforced requirements. For a homeowner, that means your city or county building department is the authority on what your roof must meet.
How to check the fire rating of your roof
You do not need to climb up and look for a stamp. Shingle fire ratings are documented, not visible. The University of California guide lists these routes: ask the manufacturer or your local building department, check the manufacturer's website, or consult a licensed roofing contractor. It adds that installation instructions can help identify an assembly-rated Class A covering.
Here is a simple order to work through:
- Find the paperwork. The permit from the last roof installation, the contractor's invoice and any warranty documents often name the shingle product line.
- Look up the product. Match the product line to the manufacturer's technical data sheet, which states the fire class and the assembly it was tested in.
- Confirm the assembly. Check whether the underlayment and installation method match the listing.
- Ask the building department. If the paperwork is gone, the permit record for your address can show what was installed.
- Note the roof's age and condition. A rating describes a new, properly installed assembly. Cracked, curled and granule-stripped shingles are a different story.
Our 15-minute roof check for shingle fire resistance walks through what a homeowner can observe from the ground, and our fire safety tips for shingle roofs cover the habits that reduce ember risk around the home.
Why condition matters as much as the label
A rating is earned by a new roof in a lab. Your roof has spent years under Florida sun, heat, rain and storms. Those conditions dry out asphalt shingles, which can turn brittle, crack, curl and shed granules. As the surface wears, the roof you have may no longer match the roof that was tested.
That is why we look at condition first. If a roof is still maintainable, preserving it can be a far better use of money than a full tear-off. Our roof assessment guide explains what we look at, and our piece on asphalt shingle composition shows which materials signal a salvageable roof.
If you do need to replace, a fire class is one criterion among several. For South Florida examples, see our list of fire-resistant roofing examples for South Florida homes.
Class A vs Class C: how to decide
Use this short framework.
- If your roof is already Class A and in good shape, the goal is to keep it that way. Preventative maintenance matters more than any upgrade.
- If your roof is Class C or unknown, confirm what you have first, then check what your building department requires. Do not assume replacement is the only answer until a professional has assessed the roof.
- If you are replacing anyway, choose an assembly listed Class A and make sure the installer follows the listed assembly, because substitutions can affect insurance and code compliance.
- If you are comparing quotes, ask each bidder for the assembly listing, not only the shingle name. Impact class is a separate line item.
Insurance adds one more layer. How your policy values a roof, replacement cost or actual cash value, changes what an aging roof costs you in a claim. Our guide to ACV vs RCV roofs explains the difference.
What we offer before you replace
We are not roofers and we are not roof cleaners. We are the company homeowners call before replacing their roof. A full replacement in South Florida can run $15,000 to $30,000, and many homeowners never learn that their roof may still be maintainable.
Our process has three steps: we inspect the roof, assess its condition, and recommend whether it qualifies for renewal. If your asphalt shingle roof qualifies, our certified Fresh Roof Green Soy Technology is designed to restore flexibility, slow deterioration and lock in granules, and you could save up to 80% compared with a full replacement. The work comes with a 6-year transferable warranty. We serve homes in Broward and Palm Beach counties.
The assessment is free. Schedule a free roof assessment and find out whether your roof qualifies, or read how the service works.

If you are in Boca Raton, Delray Beach or Plantation, we have local pages for you: Boca Raton, Delray Beach and Plantation.
Our perspective
Most homeowners who ask about Class A and Class C are really asking a bigger question: is my roof still good enough, or do I have to start over? The letter on a data sheet cannot answer that. Condition can.
We see the roof as something you maintain, not something you wait to fail. Florida's sun and heat dry out shingles over time, and the earlier you catch that, the more options you keep. That is why our message is simple: call us before you call the roofer.
Our Green Soy Technology is built around restoring flexibility at the molecular level, locking in granules and extending the life of qualifying asphalt shingle roofs. Our fire safety benefits are part of why homeowners choose preservation, and our assessments are honest: if a roof does not qualify, we tell you.
Check your rating, know your assembly, and get the roof looked at while renewal is still on the table.
Daniellison
FAQ
Is Class A or Class C better for shingles?
Class A is better. It means the roof covering was effective against severe fire-test exposure, while Class C covers only light exposure. In the standard test, Class A allows a maximum flame spread of 6 feet versus 13 feet for Class C.
What is the difference between Class A and Class 3 or Class 4 shingles?
They measure different things. Class A, B and C are fire ratings under UL 790 or ASTM E108. Class 1 to 4 are impact ratings under UL 2218, based on steel balls dropped to simulate hail. A shingle can carry one of each.
Does the shingle alone determine the fire rating?
Not always. The result can depend on the covering, underlayment and installation tested together. Substituting parts of a tested assembly may need approval and can affect insurance coverage or local code compliance.
How do I find out my roof's fire rating?
Ask the shingle manufacturer or your local building department, check the manufacturer's website, or consult a licensed roofing contractor. Old permits and invoices that name the shingle line make the search much faster.
Can an aging roof still be worth keeping?
Often, yes. If the shingles are still maintainable, preservation can cost far less than replacement. We offer a free assessment in Broward and Palm Beach counties to tell you whether your roof qualifies.
Sources
- Class A, B, and C Roof Ratings (UL)
- Roof Covering, Homeowner's Wildfire Mitigation Guide (UC ANR)
- ASTM E108: Fire Tests of Roof Coverings (Intertek)
- Asphalt Shingle Roofs, Building America Solution Center
- Class 1 and Class A Roof Assemblies
- Construction Concerns: Roofing Materials Tests (Fire Engineering)
- Roofing Testing and Certification Services (UL Solutions)
- UL Solutions and IBHS on residential roofing shingles
- Relative Impact Resistance of Asphalt Shingles (IBHS)
- Roofing best practices (IBHS)
- The Underlying Truth About Roofing Underlayments (UL)
- Code Standards and Ensuring Roofs
